Platinum Compounds in Nanotubes
September 11, 2017 – Researchers from Nottingham, Ulm, Birmingham, Leeds and further UK partners have grown nanocrystals of platinum diiodide and platinum disulfide inside carbon nanotubes about 1.5 nm wide, with platinum and iodine or sulfur in the exact ratio 1:2. The key is a single precursor molecule that carries all elements in the right proportion. AC-HRTEM at 80 kV on an FEI Titan in Ulm, backed by image simulations, revealed how the crystals repack to fit the tube; HAADF-STEM at 200 kV on a probe-corrected JEOL 2100F in Birmingham validated the structures and told platinum from iodine.
Platinum diiodide and platinum disulfide are hard to make as nanocrystals by conventional chemistry. Researchers from the University of Nottingham, Ulm University, the University of Birmingham, the University of Leeds and further partners in the UK have now grown both inside single-walled carbon nanotubes only about 1.5 nm wide, and with the right ratio of the elements. The trick is a single molecular precursor that already carries platinum and iodine or sulfur in the ratio 1:2. Aberration-corrected high-resolution transmission electron microscopy (AC-HRTEM) at 80 kV in Ulm, on an FEI Titan 80-300 with a Cs corrector, revealed the atomic structure of every product, and image simulations confirmed it. High-angle annular dark-field scanning TEM (HAADF-STEM) at 200 kV in Birmingham, on a JEOL 2100F with a CEOS probe corrector, validated the structures with a second imaging mode that tells platinum from iodine by its brightness. Energy-dispersive X-ray (EDX) spectroscopy measured the composition.
Nanotubes as reaction vessels
The narrow channel of a carbon nanotube fixes the positions of the atoms and molecules inside it, and it can steer chemical reactions. Reactions inside nanotubes have produced sulfur-terminated graphene nanoribbons that synthetic chemistry can hardly make[1],[2], and even the elusive carbon chain carbyne[3]. Inorganic compounds such as lanthanide halides[4], potassium iodide[5], cobalt iodide[6] and barium diiodide[7] are usually brought into nanotubes from the melt: the open tubes are dipped into the molten compound and capillary forces draw cations and anions into the channel in the right ratio. HRTEM has imaged such crystals atom by atom since 2000[8].
Many compounds cannot be melted without decomposing, however. For them, the nanotube can serve as a reaction vessel: first a metal is brought in, then a second element that reacts with it. Inside nanotubes, the same team had already turned metal carbonyls and iodine into identical metal iodide clusters and then into MoS2 and WS2 nanoribbons (see Inorganic Synthesis in Carbon Nanotubes)[9]. The new study asks how well this works with platinum and how the ratio of the elements can be controlled.
Step by step: platinum, iodide, sulfide
In the stepwise route, molecules of platinum acetylacetonate, Pt(acac)2, were sublimed into the nanotubes and heated to 500 °C. The organic ligands left as gas, and the platinum atoms gathered into small cylindrical nanoparticles, on average 1.5 nm long and 1.0 nm wide (Fig. 1). AC-HRTEM shows their lattice planes 240–270 pm apart, much closer than the platinum atoms in the iodide and sulfide formed later, and in line with metallic platinum rather than a carbide or oxide. Iodine vapour then turned the particles into platinum iodide, and hydrogen sulfide at 550 °C turned the iodide into platinum sulfide, all inside the same tubes. The recipes for both routes are given in the box below.
The problem of the right ratio
The tubes held the products in shape, but the composition went astray. EDX showed far too much iodine in the platinum iodide made step by step, and after the reaction with hydrogen sulfide the sulfide still contained iodine and a large excess of sulfur. Iodine is more volatile than the platinum precursor and always enters the tubes in excess, and it is hard to remove again. Mixing Pt(acac)2 and iodine before filling, a one-pot approach as in preparative chemistry, saved steps but did not solve the problem. Yet even small deviations from the exact composition change the properties of inorganic materials drastically, as nitrogen does in diamond or carbon in boron nitride[13],[14].
One molecule, the right recipe
The solution is a precursor that already contains everything in the right proportion. A platinum atom in Pt(acac)2 has four neighbours in a plane; two more ligands can bind above and below it. With two iodide or two thiocyanate ligands there, every molecule carries exactly one platinum atom and two atoms of iodine or sulfur. Once inside the nanotube, the molecule only has to be heated: the organic parts leave as gas, and platinum reacts with its two partners. The authors call it a one-pot-one-reactant synthesis. EDX found a platinum-to-iodine ratio of 1:2.11 and a platinum-to-sulfur ratio of 1:1.93, close to the ideal 1:2. How the two routes compare is shown in the box below (Table 1).
Platinum iodide repacked for the tube
AC-HRTEM at 80 kV showed nanotubes almost completely filled with crystalline platinum iodide along their whole length (Fig. 2a). In a representative tube 1.52 nm wide, which corresponds to an (11,11) nanotube, the crystal forms a close-packed lattice that is nearly cubic (Fig. 2b, c). Bulk PtI2 crystallizes in a monoclinic cell of 659 × 871 × 689 pm[15]. Such a cell would fit into the tube but leave a large void, so the atoms rearrange. Each platinum atom keeps six iodine neighbours at the bulk distance, while the iodine atoms take between one and six platinum neighbours, three on average: highly coordinated iodine sits in the middle of the crystal, iodine with a single platinum neighbour in the gap between the platinum and the tube wall. The ratio stays 1:2 as in the bulk.
Along the tube axis, the atomic columns are 390 pm apart, compared with 381 pm between iodine atoms in bulk PtI2. This slight stretching is typical of crystals that adapt to the nanotube channel and maximize their van der Waals contact with the walls[16]. The tube itself becomes slightly elliptical to accommodate the crystal (Fig. 2d, e), as reported before for cobalt iodide[6]. Multislice image simulations of a geometry-optimized model inside an (11,11) nanotube reproduce the experimental images in two orientations, 90° apart (Fig. 2c, d, f).
Bright-field HRTEM has a limit here. Its contrast depends on thickness, crystallinity, focus and atomic number together, so platinum (Z = 78) and iodine (Z = 53) cannot be told apart without quantitative simulation. The identity of the atoms was therefore checked with a second microscope working in another mode, described after the platinum sulfide below.
Platinum sulfide with zigzag edges
Platinum disulfide made from the thiocyanate precursor also filled the nanotubes over long distances (Fig. 3a). Here AC-HRTEM resolves only the columns of platinum atoms, because sulfur (Z = 16) scatters far more weakly than platinum. The platinum atoms form a hexagonal lattice as in bulk PtS2 (Fig. 3b). In a tube 1.32 nm wide, the Pt–Pt spacings of 370 and 390 pm match a PtS2 lattice tilted by 45° (Fig. 3c). The edges of the crystal have a zigzag shape, with only sulfur atoms touching the tube wall (Fig. 3d). EDX confirmed the composition of both products directly on the tube bundles.
Both crystals were also imaged with a second aberration-corrected microscope working in another mode, as described in the box below, which also holds the STEM images (Fig. 4) and two tables comparing the microscopes and their results.
Simulation and measurement agree
Every structure was checked against image simulations and against the known bulk crystals. For platinum iodide, simulated images of the geometry-optimized model inside an (11,11) nanotube match the experiment when the model is tilted step by step, and the measured spacings deviate only slightly from the bulk values. Measured and expected values are set side by side in the box below (Fig. 5, Table 4).
Challenges named by the authors
Neither the stepwise nor the one-pot approach controlled the stoichiometry: excess iodine always remained, even after conversion to the sulfide. In bright-field AC-HRTEM, platinum and iodine are hard to distinguish without quantitative image simulation, and in platinum sulfide only the platinum columns are visible. HAADF-STEM, in turn, does not show the nanotube wall. The one-reactant route needs a dedicated precursor for every compound, which has to be synthesized first.
Outlook
Expanding the coordination sphere of a metal complex with ligands that carry the second element turns out to be a general recipe for inorganic synthesis at the nanoscale. It gave quasi-one-dimensional PtI2 and PtS2 crystals with a near-perfect composition, materials that were not accessible in this form before. Inside their nanotubes they are already packaged for use, for instance in electronic devices or as catalysts whose shape is set by the host tube.
Resource:
Stoppiello, C. T., Biskupek, J., Li, Z. Y., Rance, G. A., Botos, A., Fogarty, R. M., Bourne, R. A., Yuan, J., Lovelock, K. R. J., Thompson, P., Fay, M. W., Kaiser, U., Chamberlain, T. W., Khlobystov, A. N. (2017).
A one-pot-one-reactant synthesis of platinum compounds at the nanoscale.
Nanoscale 9(38), 14385–14394.
https://doi.org/10.1039/c7nr05976k
Download this news article as PDF – for reading on paper, taking notes or filing.
-
Chuvilin, A., Bichoutskaia, E., Gimenez-Lopez, M. C., Chamberlain, T. W., Rance, G. A., Kuganathan, N., Biskupek, J., Kaiser, U., Khlobystov, A. N. (2011). Self-Assembly of a Sulphur-Terminated Graphene Nanoribbon Within a Single-Walled Carbon Nanotube. Nature Mater, 10, 687–692. https://doi.org/10.1038/nmat3082
-
Chamberlain, T. W., Biskupek, J., Rance, G. A., Chuvilin, A., Alexander, T. J., Bichoutskaia, E., Kaiser, U., Khlobystov, A. N. (2012). Size, Structure, and Helical Twist of Graphene Nanoribbons Controlled by Confinement in Carbon Nanotubes. ACS Nano, 6, 3943–3953. https://doi.org/10.1021/nn300137j
-
Shi, L., Rohringer, P., Suenaga, K., Niimi, Y., Kotakoski, J., Meyer, J. C., Peterlik, H., Wanko, M., Cahangirov, S., Rubio, A., Lapin, Z. J., Novotny, L., Ayala, P., Pichler, T. (2016). Confined Linear Carbon Chains as a Route to Bulk carbyne. Nature Mater, 15, 634–639. https://doi.org/10.1038/nmat4617
-
Xu, C., Sloan, J., Brown, G., Bailey, S., Williams, V. C., Friedrichs, S., Coleman, K. S., Flahaut, E., Green, M. L. H., Hutchison, J. L., Dunin-Borkowski, R. E. (2000). 1D Lanthanide Halide Crystals Inserted Into Single-Walled Carbon Nanotubes. Chem. Commun., , 2427–2428. https://doi.org/10.1039/b006817i
-
Sloan, J., Novotny, M., Bailey, S., Brown, G., Xu, C., Williams, V., Friedrichs, S., Flahaut, E., Callender, R., York, A., Coleman, K., Green, M., Dunin-Borkowski, R., Hutchison, J. (2000). Two Layer 4:4 Co-Ordinated KI Crystals Grown Within Single Walled Carbon Nanotubes. Chem. Phys. Lett., 329, 61–65. https://doi.org/10.1016/S0009-2614(00)00998-2
-
Philp, E., Sloan, J., Kirkland, A. I., Meyer, R. R., Friedrichs, S., Hutchison, J. L., Green, M. L. H. (2003). An Encapsulated Helical One-Dimensional Cobalt Iodide Nanostructure. Nature Mater, 2, 788–791. https://doi.org/10.1038/nmat1020
-
Sloan, J., Grosvenor, S. J., Friedrichs, S., Kirkland, A. I., Hutchison, J. L., Green, M. L. H. (2002). A One-Dimensional BaI2 Chain With Five- and Six-Coordination, Formed Within a Single-Walled Carbon Nanotube. Angew. Chem. Int. Ed., 41, 1156–1159. https://doi.org/10.1002/1521-3773(20020402)41:7<1156::AID-ANIE1156>3.0.CO;2-N
-
Meyer, R. R., Sloan, J., Dunin-Borkowski, R. E., Kirkland, A. I., Novotny, M. C., Bailey, S. R., Hutchison, J. L., Green, M. L. H. (2000). Discrete Atom Imaging of One-Dimensional Crystals Formed Within Single-Walled Carbon Nanotubes. Science, 289, 1324–1326. https://doi.org/10.1126/science.289.5483.1324
-
Botos, A., Biskupek, J., Chamberlain, T. W., Rance, G. A., Stoppiello, C. T., Sloan, J., Liu, Z., Suenaga, K., Kaiser, U., Khlobystov, A. N. (2016). Carbon Nanotubes as Electrically Active Nanoreactors for Multi-Step Inorganic Synthesis: Sequential Transformations of Molecules to Nanoclusters and Nanoclusters to Nanoribbons. J. Am. Chem. Soc., 138, 8175–8183. https://doi.org/10.1021/jacs.6b03633
-
Fu, Q., Weinberg, G., Su, D. (2008). Selective Filling of Carbon Nanotubes With Metals by Selective Washing. New Carbon Mater., 23, 17–20. https://doi.org/10.1016/S1872-5805(08)60008-6
-
Cook, P. M., Dahl, L. F., Hopgood, D., Jenkins, R. A. (1973). Oxidative-Addition Reaction of Platinum Acetylacetonate With Iodine in Solid State and Solution. Crystal structure and equilibrium studies of trans-bis(acetylacetonato)di-iodoplatinum(IV). J. Chem. Soc., Dalton Trans., , 294. https://doi.org/10.1039/dt9730000294
-
Grabowski, A., Preetz, W. (1987). Darstellung und Schwingungsspektren von trans-[Pt(acac)2X2] (X = Cl, Br, I, SCN, SeCN, N3). Z. Anorg. Allg. Chem., 544, 95–100. https://doi.org/10.1002/zaac.19875440109
-
Baranauskas, V., Li, B. B., Peterlevitz, A., Tosin, M. C., Durrant, S. F. (1999). Nitrogen-Doped Diamond Films. J. Appl. Phys., 85, 7455–7458. https://doi.org/10.1063/1.369378
-
Zhao, J., Dai, B. (2004). DFT Studies of Electro-Conductivity of Carbon-Doped Boron Nitride Nanotube. Mater. Chem. Phys., 88, 244–249. https://doi.org/10.1016/j.matchemphys.2003.10.018
-
Thiele, G., Weigl, W., Wochner, H. (1986). Die Platiniodide PtI2 und Pt3I8. Z. Anorg. Allg. Chem., 539, 141–153. https://doi.org/10.1002/zaac.19865390813
-
Kiselev, N., Zakalyukin, R., Zhigalina, O., Grobert, N., Kumskov, A., Grigoriev, Y. V., Chernysheva, M., Eliseev, A., Krestinin, A., Tretyakov, Y., Freitag, B., Hutchison, J. (2008). The Structure of 1D CuI Crystals Inside SWNTs. J. Microsc., 232, 335–342. https://doi.org/10.1111/j.1365-2818.2008.02104.x
-
Wang, Z. W., Li, Z. Y., Park, S. J., Abdela, A., Tang, D., Palmer, R. E. (2011). Quantitative Z-Contrast Imaging in the Scanning Transmission Electron Microscope With Size-Selected Clusters. Phys. Rev. B, 84, 073408. https://doi.org/10.1103/PhysRevB.84.073408
-
Rez, D., Rez, P., Grant, I. (1994). Dirac–Fock Calculations of X-Ray Scattering Factors and Contributions to the Mean Inner Potential for Electron Scattering. Acta Crystallogr. A, 50, 481–497. https://doi.org/10.1107/S0108767393013200
-
He, D., Li, Z., Yuan, J. (2015). Kinematic HAADF-STEM Image Simulation of Small Nanoparticles. Micron, 74, 47–53. https://doi.org/10.1016/j.micron.2015.04.005





