Hybrid MoSe2–WSe2 Heterostructures
July 25, 2026 – Researchers from FSU Jena, the Technical University of Darmstadt, and Ulm University (Germany) and the National Institute for Materials Science in Tsukuba (Japan) have grown purely lateral and hybrid lateral/vertical heterostructures of MoSe2 and WSe2 monolayers in a single chemical vapor deposition step from liquid metal-salt precursors, in the growth reactor that Antony George and colleagues built up in Jena. Which of the two types forms is set simply by the Mo:W ratio of the precursor solution. Electron microscopy at Ulm University shows lateral interfaces only about 5 nm wide, and HRTEM shows continuous atomic rows without moiré and electron diffraction a single set of sharp spots, evidence of epitaxial growth of the top layer, which forms domains of two stacking orders.
Two atomically thin semiconductors can be joined in two ways: stitched together edge to edge within a single atomic layer, or stacked one on top of the other. Monolayer transition metal dichalcogenides (TMDs) such as MoSe2 and WSe2 lend themselves to both, and the resulting heterostructures hold considerable promise for new electronic, optoelectronic and photonic devices as well as for the study of emergent quantum phenomena[1]. They give access to effects that do not exist in an isolated monolayer, such as interlayer excitons and charge-transfer excitons in lateral heterostructures[2] or electrical transport through one-dimensional p–n junctions[3]. Because the two materials are structurally so similar, they can form lateral TMD1–TMD2 junctions as well as vertical TMD1/TMD2 van der Waals stacks, and both architectures host a rich variety of excitonic phenomena while remaining easy to integrate into devices[4],[5]. Lateral heterostructures, for instance, guide excitons in one direction only[6], a prerequisite for excitonic circuits, and their spatially modulated electronic properties allow atomically thin, in-plane p–n junctions for transistors, diodes, photodetectors, photovoltaic and electroluminescent systems and other quantum devices[3],[7]–[9].
Vertical heterostructures, in turn, are best known for interlayer excitons, bound electron–hole pairs whose two partners sit in two adjacent monolayers[10],[11]. The MoSe2/WSe2 stack is the prime example: its type-II band alignment, in which the lowest conduction band lies in one layer and the highest valence band in the other, drives a rapid transfer of charge between the MoSe2 and WSe2 layers. The result is long-lived interlayer excitons[12], an attractive feature for quantum encryption and for valleytronics, which uses the valley degree of freedom of the electrons to encode information[13]–[15]. Interlayer excitons trapped in moiré potentials moreover emit at discrete energies, which makes them candidates for single-photon emitters[15] and, when coupled to nanocavities, for nanoscale lasers[16].
For fundamental studies and for applications alike, such heterostructures have to be grown from the bottom up, so that they can be produced at scale and are compatible with semiconductor and optical technologies. This is usually done by chemical vapor deposition (CVD), either in one step[5],[17],[18] or in several[9],[19]. Most of these approaches rely on solid precursors: transition metal oxide powders such as MoO3 and WO3, chalcogens (S and Se) or pre-synthesized TMD mixtures such as WSe2 and MoSe2[1]. Only a few studies have so far used liquid precursors to grow TMD heterostructures[20]–[22]. Metal–organic liquid precursors have served to grow lateral heterostructures, while ammonium- and sodium-based salts have yielded lateral[20] and vertical MoS2–WS2 heterostructures for transport studies[21], and sodium-based salts have produced lateral MoSe2–WSe2 heterostructures for photodetectors[22].
Hossain et al. grow both kinds in a single CVD step from liquid metal-salt precursors: purely lateral heterostructures (HS I) and hybrid lateral/vertical ones (HS II). The recipe itself is simple. Aqueous solutions of the metal salts are spin-coated onto the substrate and converted in a CVD reactor with quartz Knudsen-type effusion cells, which control the flow of selenium vapor precisely. Antony George built up this type of reactor at FSU Jena[23] (see the box below). The furnace is heated to 770 °C, 820 °C or 900 °C at a constant rate of 15 °C min−1. Because the Mo species has a lower melting point and a higher vapor pressure[3], MoSe2 nucleates first, and WSe2 then grows epitaxially from its edges. Which structure forms is set by the ratio of the two metals in the precursor. At a high Mo:W ratio of 3:1, bilayer MoSe2 islands form and likely act as nucleation sites for the subsequent WSe2 growth, yielding the vertical HS II. At a low ratio of 1:3, monolayer MoSe2 grows and WSe2 is stitched laterally to it, giving HS I. Control experiments that grew MoSe2 alone at high and low Na2MoO4 concentrations, corresponding to the values 3 and 1 in the precursor ratios, confirmed this mechanism: they yielded mainly bilayer islands or monolayer MoSe2, respectively. The heating rate turned out to be critical as well. Only at 15 °C min−1 did phase-pure MoSe2–WSe2 lateral heterostructures form; at 40 °C min−1, the heterostructures were of mixed phase, in line with the fast growth kinetics of TMD monolayers under these conditions[24].
For the microscope, the heterostructures were lifted off their growth substrate with a film of poly(methyl methacrylate) (PMMA) in potassium hydroxide solution, placed on copper grids coated with a lacey carbon film and freed of the PMMA in a CO2 critical-point dryer. A Thermo Fisher Talos F200X with a SuperX four-quadrant detector for energy-dispersive X-ray spectroscopy (EDX) was operated at 80 kV, which reduces knock-on damage and raises the EDX signal, and at 200 kV, where contamination in scanning TEM (STEM) mode is lower and the spatial resolution in TEM and STEM is higher. Each EDX map was summed from several drift-corrected scans of 512 × 512 pixels over about 10 minutes.
Fig. 1 shows an entire HS I flake as the electron microscope sees it. The overview (Fig. 1a) was taken at 200 kV by high-angle annular dark-field (HAADF) STEM: a finely focused electron beam scans the sample, and an annular detector collects the electrons scattered to high angles. In it, the six-pointed star measures about 7 µm from tip to tip and lies across the round holes of the support film. The EDX maps of the same area (Fig. 1b–d) take the flake apart element by element: Mo fills the inner star, W traces a band less than 1 µm wide along all six edges, and Se covers the entire flake, as expected for two selenides joined within a single layer. Mo and W belong to the same group of the periodic table, and MoSe2 and WSe2 share the same hexagonal lattice with nearly the same spacing, so the two can be joined within one layer; what tells them apart in the microscope is their atomic number, 42 for Mo and 74 for W. Each map records the characteristic X-rays that one element emits when the scanned electron beam knocks out an inner-shell electron, so the brightness of a pixel shows how much of that element the beam passed through. The maps thereby record the growth sequence described above: MoSe2 nucleated first, and WSe2 then grew epitaxially from its edges, so the W band follows the six-pointed outline of the MoSe2 core. The maps of the whole star thus show at a glance what the high-magnification images in Fig. 2 then resolve down to a few nanometers: where Mo ends and W begins.
HS I is a MoSe2 monolayer surrounded by a WSe2 monolayer, stitched together edge to edge (Fig. 1). In HAADF-STEM images the contrast depends strongly on the atomic number Z, and combined with EDX elemental mapping of the whole flake (Fig. 1) and across the interface (Fig. 2a) they showed Se distributed uniformly across the entire HS I, while Mo was localized in the center and W in the outer region. The HAADF overview of the interface region (Fig. 3a of the paper, not reproduced here) matched the EDX result, with darker contrast for the lighter Mo atoms and brighter contrast for the heavier W atoms, and it revealed an intermediate Mo1₋ₓWₓSe2 alloy region about 120 nm wide between the MoSe2 and WSe2 domains in which both metals coexist. High-magnification HAADF-STEM images showed, however, that the boundary between MoSe2 and the Mo–W–Se alloy and the boundary between the alloy and WSe2 (the latter in Fig. 2b) are each confined to only about 5 nm; the Fourier transforms of the regions on either side are shown as insets. The authors suggested that this combination of a wide alloyed zone and sharp transitions to the pure materials is possibly driven by the nucleation kinetics combined with substrate-induced effects during the one-step growth. Selected-area electron diffraction (SAED) patterns taken with the smallest aperture, from areas about 100 nm across in the three regions (Fig. 2c–e), all showed a sharp six-fold symmetry with nearly identical {10–10} lattice spacings of 0.2818 nm (MoSe2), 0.2819 nm (Mo–W–Se) and 0.2821 nm (WSe2), demonstrating a single-crystalline in-plane heterojunction in HS I. TEM analyses, including the 200 kV HAADF-STEM overview and the EDX maps of the whole flake (Fig. 1), confirm a continuous, high-quality lateral heterostructure.
The hybrid structure HS II is more complex. It consists of a bottom MoSe2 monolayer carrying a lateral MoSe2–WSe2 top layer and thus of three regions: a MoSe2 monolayer (region 1), a vertical MoSe2/WSe2 heterobilayer (region 2) and a MoSe2 homobilayer (region 3). The flakes are large on the scale of the microscope: the top lateral layer of HS II measures about 20 to 90 µm across and HS I flakes about 10 to 200 µm, and both types cover about 50–90 % of the growth substrate. Higher growth temperatures enlarged HS I, and more W precursor expanded the WSe2 domains about two- to three-fold. The electron microscope looks into windows of this, from fields of view of a few micrometers down to a few nanometers.
The critical-point drying that removes the PMMA before imaging ran in several stages. After the PMMA-covered flake had been floated off its SiO2/Si substrate on 2 M potassium hydroxide solution, rinsed in ultrapure water and placed on the grid, it was baked at 90 °C for 10 minutes so that it adheres to the lacey carbon. In the dryer, the sample was first kept in acetone for 45 minutes; the acetone was then replaced by liquid CO2 at about −2 °C and 5 MPa, and finally the CO2 was brought into its supercritical state at 38 °C and 10 MPa for 10 minutes. Transfers onto gold Quantifoil grids were done without any PMMA, using isopropanol and KOH as transfer agents. Gabriele Es-Samlaoui assisted with the preparation of the TEM samples.
At 200 kV, the lateral MoSe2–WSe2 interface in the top layer turned out to be exceptionally narrow, only about 5 nm wide (Fig. 3a, b). The W signal in the EDX maps (Fig. 3a) is stronger on the heterobilayer side of the dashed line, while Mo and Se continue across it, as the MoSe2 monolayer underneath runs through the whole flake. In the HAADF image (Fig. 3b), the heterobilayer on the right appears brighter than the MoSe2 homobilayer on the left: both are two layers thick, but the heavier W atoms scatter more electrons to high angles than Mo. In the high-resolution image (Fig. 3b), the lattice fringes run through the transition zone, marked red between the cyan and yellow bars. The red segments at the top and bottom edges are offset against each other because the interface runs obliquely through the image; the white dashed arrows follow its course. The team attributed this sharpness to the epitaxial growth of the top lateral heterostructure directly on the MoSe2 monolayer underneath. The HRTEM image of the vertical region (Fig. 3c) supports this interpretation: it shows continuous atomic rows without any visible moiré pattern. The SAED patterns of the heterobilayer (Fig. 3d) and of the MoSe2 homobilayer (Fig. 3e) each consist of a single set of sharp, circular Bragg spots with six-fold symmetry. Non-epitaxial growth of the second layer, or a twisted bilayer, would instead produce moiré fringes in HRTEM and split spots in diffraction, so the authors regard both findings as direct evidence of epitaxial alignment. A Fourier transform of an HRTEM image acts like a computed diffraction pattern of the imaged area: each set of lattice fringes gives a pair of spots, so a single, undisturbed lattice gives a single hexagon. The Fourier transform of the HRTEM image (inset in Fig. 3c) likewise shows one hexagonal set of sharp spots. The homobilayer pattern (Fig. 3e) carries the same message for the other half of the top layer: there, MoSe2 grew on MoSe2, and the six-fold pattern with circular spots indicates that this part of the top layer is also epitaxially aligned with the monolayer underneath. Panels a–e were all recorded at 200 kV, where contamination in STEM mode is lower and the spatial resolution in TEM and STEM is higher than at 80 kV; in TEM mode the beam current was about 5 nA. The colored bars along the top and bottom edges of Fig. 3b follow the same code as the region labels: cyan for the MoSe2 homobilayer, red for the transition zone and yellow for the MoSe2/WSe2 heterobilayer. Read from left to right, they mark a junction only about 5 nm wide; in HS I, by contrast, a 120 nm alloy zone lies between the two pure materials. In diffraction, a second layer rotated against the first would add its own hexagon of spots, turned by the twist angle. Because the lattice spacings of MoSe2 and WSe2 differ by only about 0.1 % (Fig. 2c–e), the spots of the two layers coincide in the pattern of the heterobilayer (Fig. 3d).
At 80 kV, HAADF-STEM and EDX maps of part of an HS II flake on the lacey carbon film (Supporting Information, Fig. S16, not reproduced here) set region 2 apart from regions 1 and 3 by its composition. Region 2 contained nearly equal atomic fractions of Mo and W, 14.4 % and 15.9 %, as expected for a vertical MoSe2/WSe2 heterobilayer, whereas regions 1 and 3 were dominated by Mo, with 30.6 % and 28.6 % Mo against only 1.5 % and 2.6 % W. Se made up about 69–70 % everywhere. Composition alone cannot tell regions 1 and 3 apart, since both consist of MoSe2 only; they differ only in thickness. The maps were recorded in STEM mode with a probe current of 100 to 200 pA and an energy dispersion of 5 eV per channel over 0–20 keV. Because the monolayer regions give a low signal-to-noise ratio, the faint signals outside the flake in the maps are background noise only.
A larger HRTEM image of the top lateral heterostructure (Fig. 4a) shows the atomic rows running on continuously from the MoSe2 homobilayer (region 3) across the interface into the MoSe2/WSe2 heterobilayer (region 2), again without visible moiré and indicative of epitaxial growth of the top layer. Fourier transforms of the three areas (Fig. 4b–d) and magnified views of a single diffraction spot from each (Fig. 4e–g) trace the transition: regions 2 and 3 show narrower fringes, the interface a wider one, and the fringe shift between regions 2 and 3 supports a transitional boundary from homobilayer to heterobilayer. The authors note that amorphous and graphitic hydrocarbon residues left by the transfer cover the lattice and lower the quality of the HRTEM images.
The small lattice mismatch between MoSe2 and WSe2 allows the vertically stacked monolayers to reconstruct, which gives rise to rich excitonic features[34]. To determine how the two layers are stacked, the team combined HAADF and annular dark-field (ADF) imaging (Fig. 5a, b) with local SAED measurements. HAADF contrast is dominated by the atomic number, whereas ADF contrast and the relative intensities of the diffraction spots are sensitive to the stacking configuration[35],[36]. Both images showed one-dimensional stripes, but only the ADF image (Fig. 5b) clearly resolved alternating brighter and darker domains, labeled α and β, indicating that the top WSe2 monolayer forms domains with different stacking orders on the bottom MoSe2 monolayer. The difference between the two detectors explains why. The HAADF detector collects electrons scattered to high angles, mostly incoherently, so its signal depends mainly on the atomic numbers in the beam path, which are the same in both domains. The ADF detector sits at lower angles and also picks up diffracted, coherent intensity, which depends on how the atoms of the two layers lie above each other. For the second-order {11–20} spots, the waves scattered by all atoms add up in phase whatever the stacking, so these spots serve as a reference. The first-order {10–10} spots, in contrast, are sensitive to the stacking, and their intensity relative to the second-order spots (Fig. 5i, j of the paper, not reproduced here) distinguishes the two stackings. The team compared four spots along one row, numbered 1 to 4: positions 2 and 3 are first-order spots, positions 1 and 4 second-order ones.
In the SAED pattern from domain α, the first- and second-order diffraction spots had comparable intensities, consistent with AB (H-like) stacking[35],[36]. In the pattern from domain β, the first-order spots were markedly weaker than the second-order ones, indicating AA (R-like) stacking[35],[36]. HRTEM further supports the coexistence of both. A 200 kV HRTEM image of a region marked in the ADF image (Fig. 5b, c) shows, magnified, areas of AA (R-like) and AB (H-like) stacking side by side (Fig. 5d). In AA (R-like) stacking, the Se atoms of WSe2 sit above the Mo atoms of MoSe2; in AB (H-like) stacking, the W (Se) atoms of WSe2 sit above the Se (Mo) atoms of MoSe2, forming a hollow hexagonal pattern when viewed from above (Fig. 5e, f). The heterobilayer of HS II thus contains a hybrid of both stacking domains; in the words of the authors, it exhibits mesoscopic reconstruction and mixed stacking domains. How these interfaces compare with an earlier MoSe2–WSe2 junction from the reactor of Antony George, imaged atom by atom in the SALVE microscope at 80 kV, is shown in the box below (Fig. 6).
By simply adjusting the precursor concentration, the one-step growth from liquid metal salts thus selects between purely lateral and hybrid lateral/vertical MoSe2–WSe2 heterostructures, and electron microscopy at Ulm University showed that the interfaces between the materials are only about 5 nm wide and that the top layer grows in epitaxial alignment with the one below. The authors envision that the simple growth process will enable the rapid synthesis of such complex heterostructures for excitonic devices, and they conclude that it "can readily offer a scalable alternative to manually assembled HSs and can be integrated into nanoelectronic and photonic devices."
Resource:
Hossain, M. T., et al. (2026).
CVD grown hybrid MoSe2–WSe2 lateral/vertical heterostructures with strong interlayer exciton emission.
Adv. Mater., e74172.
https://doi.org/10.1002/adma.74172
Download this news article as PDF – for reading on paper, taking notes or filing.
-
Liu, M., et al. (2025). 2D TMD-Based Lateral Heterostructures: Preparation, Property, and Application. Advanced Functional Materials, 35, 2500876. https://doi.org/10.1002/adfm.202500876
-
Rosati, R., Paradisanos, I., Huang, L., Gan, Z., George, A., et al. (2023). Interface Engineering of Charge-Transfer Excitons in 2D Lateral Heterostructures. Nature Communications, 14, 2438. https://doi.org/10.1038/s41467-023-37889-9
-
Najafidehaghani, E., Gan, Z., George, A., et al. (2021). 1D p–n Junction Electronic and Optoelectronic Devices From Transition Metal Dichalcogenide Lateral Heterostructures Grown by One-Pot Chemical Vapor Deposition Synthesis. Advanced Functional Materials, 31, 2101086. https://doi.org/10.1002/adfm.202101086
-
Wang, G., et al. (2018). Colloquium: Excitons in Atomically Thin Transition Metal Dichalcogenides. Reviews of Modern Physics, 90, 021001. https://doi.org/10.1103/revmodphys.90.021001
-
Duan, X., et al. (2014). Lateral Epitaxial Growth of Two-Dimensional Layered Semiconductor Heterojunctions. Nature Nanotechnology, 9, 1024–1030. https://doi.org/10.1038/nnano.2014.222
-
Beret, D., et al. (2022). Exciton Spectroscopy and Unidirectional Transport in MoSe2-WSe2 Lateral Heterostructures Encapsulated in Hexagonal Boron Nitride. npj 2D Materials and Applications, 6, 84. https://doi.org/10.1038/s41699-022-00354-0
-
Huang, X., et al. (2024). Atomically Sharp 1D Interfaces in 2D Lateral Heterostructures of VSe2─NbSe2 Monolayers. ACS Nano, 18, 31300–31308. https://doi.org/10.1021/acsnano.4c10302
-
Wang, J., et al. (2019). Recent Advances in 2D Lateral Heterostructures. Nano-Micro Letters, 11, 48. https://doi.org/10.1007/s40820-019-0276-y
-
Zhang, Z., et al. (2017). Robust Epitaxial Growth of Two-Dimensional Heterostructures, Multi-Heterostructures, and Superlattices. Science, 357, 788–792. https://doi.org/10.1126/science.aan6814
-
Jiang, Y., et al. (2021). Interlayer exciton formation, relaxation, and transport in TMD van der Waals heterostructures. Light Science & Applications, 10, 72. https://doi.org/10.1038/s41377-021-00500-1
-
Rivera, P., et al. (2018). Interlayer Valley Excitons in Heterobilayers of Transition Metal Dichalcogenides. Nature Nanotechnology, 13, 1004–1015. https://doi.org/10.1038/s41565-018-0193-0
-
Kremser, M., et al. (2020). Discrete Interactions Between a Few Interlayer Excitons Trapped at a MoSe2–WSe2 Heterointerface. npj 2D Materials and Applications, 4, 8. https://doi.org/10.1038/s41699-020-0141-3
-
Jiang, C., et al. (2018). Microsecond Dark-Exciton Valley Polarization Memory in Two-Dimensional Heterostructures. Nature Communications, 9, 753. https://doi.org/10.1038/s41467-018-03174-3
-
Ye, T., et al. (2022). Nonvolatile Electrical Switching of Optical and Valleytronic Properties of Interlayer Excitons. Light: Science & Applications, 11, 23. https://doi.org/10.1038/s41377-022-00718-7
-
Baek, H., et al. (2020). Highly energy-tunable quantum light from moiré-trapped excitons. Science Advances, 6, aba8526. https://doi.org/10.1126/sciadv.aba8526
-
Qian, C., et al. (2024). Lasing of moiré trapped MoSe2/WSe2 interlayer excitons coupled to a nanocavity. Science Advances, 10, adk6359. https://doi.org/10.1126/sciadv.adk6359
-
Chen, T., et al. (2019). Lateral and Vertical MoSe2–MoS2 Heterostructures via Epitaxial Growth: Triggered by High-Temperature Annealing and Precursor Concentration. Journal of Physical Chemistry Letters, 10, 5027–5035. https://doi.org/10.1021/acs.jpclett.9b01961
-
Wang, Z., et al. (2017). NaCl-Assisted One-Step Growth of MoS2–WS2 In-Plane Heterostructures. Nanotechnology, 28, 325602. https://doi.org/10.1088/1361-6528/aa6f01
-
Wang, D., et al. (2022). Few-Layer WS2–WSe2 Lateral Heterostructures: Influence of the Gas Precursor Selenium/Tungsten Ratio on the Number of Layers. ACS Nano, 16, 1198–1207. https://doi.org/10.1021/acsnano.1c08979
-
Chen, K., et al. (2015). Lateral Built-in Potential of Monolayer MoS2–WS2 In-Plane Heterostructures by a Short Cut Growth Strategy. Advanced Materials, 27, 6431–6437. https://doi.org/10.1002/adma.201502375
-
Zhu, J., et al. (2020). One-Pot Selective Epitaxial Growth of Large WS2/MoS2 Lateral and Vertical Heterostructures. Journal of the American Chemical Society, 142, 16276–16284. https://doi.org/10.1021/jacs.0c05691
-
Zhao, S., et al. (2024). Tunable WSe2–MoSe2 Lateral Heterojunction Photodetector Based on Piezoelectric and Flexoelectric Effects. ACS Applied Materials & Interfaces, 16, 67889–67899. https://doi.org/10.1021/acsami.4c09423
-
George, A., et al. (2019). Controlled Growth of Transition Metal Dichalcogenide Monolayers Using Knudsen-Type Effusion Cells for the Precursors. Journal of Physics: Materials, 2, 016001. https://doi.org/10.1088/2515-7639/aaf982
-
Zhang, J., et al. (2024). Toward Controlled Synthesis of 2D Crystals by CVD: Learning From the Real-Time Crystal Morphology Evolutions. Nano Letters, 24, 2465–2472. https://doi.org/10.1021/acs.nanolett.3c04016
-
Shree, S., George, A., et al. (2020). High Optical Quality of MoS2 Monolayers Grown by Chemical Vapor Deposition. 2D Materials, 7, 015011. https://doi.org/10.1088/2053-1583/ab4f1f
-
Winter, A., George, A., et al. (2018). Lateral Heterostructures of Two-Dimensional Materials by Electron-Beam Induced Stitching. Carbon, 128, 106–116. https://doi.org/10.1016/j.carbon.2017.11.034
-
George, A., et al. (2021). Giant Persistent Photoconductivity in Monolayer MoS2 Field-Effect Transistors. npj 2D Materials and Applications, 5, 15. https://doi.org/10.1038/s41699-020-00182-0
-
Gan, Z., et al. (2022). Chemical Vapor Deposition of High-Optical-Quality Large-Area Monolayer Janus Transition Metal Dichalcogenides. Advanced Materials, 34, 2205226. https://doi.org/10.1002/adma.202205226
-
Kuppadakkath, A., et al. (2022). Direct Growth of Monolayer MoS2 on Nanostructured Silicon Waveguides. Nanophotonics, 11, 4397–4408. https://doi.org/10.1515/nanoph-2022-0235
-
Paradisanos, I., Shree, S., George, A., et al. (2020). Controlling Interlayer Excitons in MoS2 Layers Grown by Chemical Vapor Deposition. Nature Communications, 11, 2391. https://doi.org/10.1038/s41467-020-16023-z
-
Lamsaadi, H., Beret, D., Paradisanos, I., Urbaszek, B., Gan, Z., George, A., Watanabe, K., Taniguchi, T., et al. (2023). Kapitza-Resistance-Like Exciton Dynamics in Atomically Flat MoSe2–WSe2 Lateral Heterojunction. Nature Communications, 14, 5881. https://doi.org/10.1038/s41467-023-41538-6
-
Lamsaadi, H., Paradisanos, I., Beret, D., Gan, Z., George, A., Watanabe, K., Taniguchi, T., Urbaszek, B., et al. (2025). Exciton Collimation, Focusing and Trapping Using Complex Transition Metal Dichalcogenide Lateral Heterojunctions. Advanced Optical Materials, 13, 2403009. https://doi.org/10.1002/adom.202403009
-
FSU Jena (2024). Jena Research Team Receives Thuringian Research Award. Press release, 18 June 2024. https://www.physik.uni-jena.de/en/iap/17028/jena-research-team-receives-thuringian-research-award
-
Zhao, S., et al. (2023). Excitons in mesoscopically reconstructed moiré heterostructures. Nature Nanotechnology, 18, 572–579. https://doi.org/10.1038/s41565-023-01356-9
-
Zeng, Z., et al. (2019). Controlled Vapor Growth and Non-Linear Optical Applications of Large-Area 3R Phase WS2 and WSe2 Atomic Layers. Advanced Functional Materials, 29, 1806874. https://doi.org/10.1002/adfm.201806874
-
Wu, Q., et al. (2024). Re-Solidified Chalcogen-Assisted Growth of Bilayer Semiconductors With Controlled Stacking Orders. Small, 20, 2305506. https://doi.org/10.1002/smll.202305506
-
Li, M.-Y., et al. (2015). Epitaxial Growth of a Monolayer WSe2–MoS2 Lateral p–n Junction With an Atomically Sharp Interface. Science, 349, 524–528. https://doi.org/10.1126/science.aab4097
-
Lin, Y.-C., et al. (2018). Stable 1T Tungsten Disulfide Monolayer and Its Junctions: Growth and Atomic Structures. ACS Nano, 12, 12080–12088. https://doi.org/10.1021/acsnano.8b04979






